Thermo King® Drive Bearings
Thermo Engine Supply stocks aftermarket drive bearings for Thermo King® transport refrigeration compressors, motors, pumps, and belt tensioners. Parts ship same day from in-stock inventory with wholesale pricing available for volume buyers. Over 35 years supporting refrigerated transport fleets.
Search by part number below or call (800) 966-3105 for bearing identification support.
Compressor & Motor Bearings
Drive bearings provide rotating-shaft support inside compressor housings and motor assemblies, maintaining alignment under continuous operation and varying refrigerant loads. Thermo Engine Supply carries replacement bearings sized and rated for Thermo King® truck, trailer, container, and APU refrigeration systems, including sealed motor bearings, shielded drive-end bearings, and pump-end support assemblies.
Bearing selection depends on shaft diameter, load rating, seal configuration, and operating temperature range. Most Thermo King® compressor applications use deep-groove ball.
All bearings in this category are aftermarket replacement parts. They are not OEM products, and we are not an authorized Thermo King® dealer or agent.
Sealed Motor
Sealed motor bearings are packed with long-life grease and require no periodic repack or external lubrication. These bearings reduce maintenance frequency and simplify scheduled service intervals, particularly on high-hour units and fleet applications where access is limited. Sealed designs are preferred in routes with extended run cycles between service windows.
Common sealed motor bearing part numbers are used in X-series motors, C-series compressors, and SLX units. Grease fill is typically lithium-based or polyurea to withstand exposure to refrigerant vapor and temperature swings from -20°F to 180°F.
Shield Bearings
Shielded bearings offer added debris protection in harsh operating environments. The shield design prevents contaminants from entering the raceway while allowing controlled airflow for heat dissipation. Shield bearings are commonly used at drive ends and in positions exposed to road dust, wash-down moisture, and under-chassis conditions typical of long-haul refrigerated transport.
Single-shield bearings allow grease fitting access on one side, while double-shield configurations are used in permanent-mount locations. Thermo Engine Supply cross-references shield type, material (steel or synthetic), and clearance class to match factory specifications.
Drive System Accessories
Drive system accessory bearings support power-transmission components outside the compressor housing, including water pump shafts, belt tensioner arms, and drive-end pulleys. We stock bearings for alternators, jackshafts, and idler assemblies across multiple Thermo King® engine and motor configurations.
Pump & Drive End
Pump-end and drive-end bearings are positioned at rotating shaft terminations where pulleys, couplers, or flex discs attach. These bearings absorb radial and axial loads from belt tension, motor torque, and misalignment forces. Proper fit and clearance at shaft ends are critical to prevent vibration, noise, and premature compressor seal failure.
Thermo Engine Supply cross-references part numbers to confirm correct bore, outer diameter, and width for each application. Typical bore sizes range from 17mm to 35mm, with C3 or C4 internal clearance to accommodate thermal expansion during compressor heat cycling.
Belt Tensioner
Tensioner bearings maintain consistent belt tracking and reduce flutter in engine-to-compressor and motor-to-compressor drive circuits. Worn tensioner bearings cause erratic belt movement, uneven wear, and power loss. Replacement tensioner bearings restore smooth operation and extend belt service life, particularly in units running multi-belt configurations or serpentine layouts.
Most tensioner assemblies use needle roller bearings or angular contact ball bearings rated for oscillating motion rather than continuous rotation. Part selection must match arm geometry and spring preload to maintain proper belt tension across the operating range.
Frequently Asked Questions
Are These Bearings Genuine Thermo King Compatible Parts?
Thermo Engine Supply bearings are aftermarket replacement parts designed to meet or exceed the fit and performance specifications of Thermo King® OEM bearings. They are not manufactured or sold by Thermo King®, and we are not affiliated with or endorsed by Thermo King®. All bearings are inspected for dimensional accuracy and tested for radial play before shipment.
How Do I Match a Part Number to My Unit?
Reference the bearing number stamped on the existing part or consult your unit's parts manual. Thermo Engine Supply part numbers are cross-referenced to Thermo King® OEM numbers where applicable. If the number is worn or unreadable, measure the bore diameter, outer diameter, and width with calipers—our team can identify the bearing from those three dimensions.
For assistance identifying a bearing by shaft diameter, housing type, or unit model, contact us at (800) 966-3105 or sales@thermoenginesupply.com. Have your unit model and serial number ready.
Do Sealed Bearings Require Periodic Lubrication?
No. Sealed bearings are pre-packed with grease and designed for the life of the bearing. Do not attempt to repack or inject grease into sealed units, as overfilling can cause seal damage and internal pressure buildup. Replace sealed bearings at recommended intervals or when noise, heat, or vibration indicates failure.
Typical service life for sealed motor bearings in transport refrigeration is 8,000–12,000 operating hours, depending on load, ambient temperature, and duty cycle. Premature failure is often caused by improper installation, misalignment, or contamination during handling.
